Development of the New Approach  for High-Side Current Sensing

Abstract

Accurate current sensing is critical in many applications including battery management, motor control, and over-current protection. Current can be sensed by either placing a small shunt resistor between the load and ground or between the battery and the load. High-side current sensing has two major advantages over low-side current sensing: it can detect high load current caused by accidental shorts, and it does not increase the resistance in the ground path. However, it does require interface circuits that can handle input common-mode voltages up to the battery voltage, which can be several tens of volts. The first part of this paper consists of a brief review of the existing approaches and methods of current sensing that widely used nowadays. This is followed by researching and development new schematic solution of the high-side current sensing which doesn’t need usage of HV amplifiers, has variable gain and has small gain error in temperature range from – 40 ºC to 125 ºC. Finally, suggested solution will be discussed and compared to existed ones. In previous current approach was used for high-side current measurement. However, this approach is not appropriative in mass production. So, the task of this work was to find out or come up with new solution, which would have same or better characteristics then previous one and would result in good yield in mass production. In reviewing the literature, several possible solutions were found. First of them is creating virtual ground for low voltage differential-input-single-output amplifier. Second approach is using fully differential system it comprises two main blocks, a differential amplifier, and an instrumentation amplifier. First approach is simple to be implemented and it doesn’t need matched high voltage transistors. However, one unanticipated  finding was that it was not easy to create build in offset, so this approach can’t measure bidirectional current. Second approach system has good noise immunity and it is to create build in offset. At the same time, it is complex because of presence of instrumental amplifier in the second stage. Instrumental amplifier is hard to design and to match. As a result, new approach is proposed. This is mixing of differential-input differential-output amplifier and virtual ground. This finding supports the ideas of previously described solutions. It has fully differential input, which results in high CMRR and PSRR, furthermore, it doesn’t require matched HV transistors because of virtual ground for amplifier. In addition, this schematic can be easily matched in terms of temperature dependence. However, new solution has a drawback, that is relatively big input current. 

Keywords

References

1. J. W. Dixon and L. A. Leal, “Current control strategy for brushless DC motors based on a common DC signal,” IEEE Trans. Power Electron., vol. 17, no. 2, pp. 232–240, Mar. 2002, DOI: 10.1109/63.988834.
2. D. A. Ward and J. L. T. Exon, “Using Rogowski coils for transient current measurements,” Eng. Sci. Educ. J., vol. 2, no. 3, p. 105, 1993, DOI: 10.1049/ESEJ:19930034.
3. S. N. Easwaran, “High-Side Current Regulation and Energy Limitation,” in Current Sensing Techniques and Biasing Methods for Smart Power Drivers, Cham: Springer International Publishing, 2018, pp. 43–71, URL: http://link.springer.com/10.1007/978-3-319-71982-5_4.
4. S. N. Easwaran, “Low-Side Current Regulation and Energy Limitation,” in Current Sensing Techniques and Biasing Methods for Smart Power Drivers, Cham: Springer International Publishing, 2018, pp. 73–91, URL: http://link.springer.com/10.1007/978-3-319-71982-5_5.
5. P. Gray, P. Hurst, S. Lewis, and R. Meyer, Analysis and Design of Analog Integrated Circuits. New York, USA: John Wiley & Sons, Inc., 2010, ISBN: 978-0-470-24599-6.
6. Chucheng Xiao, Lingyin Zhao, T. Asada, W. G. Odendaal, and J. D. van Wyk, “An overview of integratable current sensor technologies,” in 38th IAS Annual Meeting on Conference Record of the Industry Applications Conference, 2003., 2003, vol. 2, pp. 1251–1258, DOI: 10.1109/IAS.2003.1257710.
7. B. Razavi, Design of Analog CMOS Integrated Circuits. New York: McGraw-Hill Education, 2017, ISBN: .
8. F. O. Eynde, P. Wambacq, and W. Sansen, “On the relationship between the CMRR or PSRR and the second harmonic distortion of differential input amplifiers,” IEEE J. Solid-State Circuits, vol. 24, no. 6, pp. 1740–1744, 1989, DOI: 10.1109/4.45014.
9. J. Baker, CMOS: Circuit Design, Layout, and Simulation, 4th Edition. Wiley-IEEE Press, 2019, ISBN: 978-1-119-48151-5.
10. W. Surakampontorn, V. Riewruja, K. Kumwachara, C. Surawatpunya, and K. Anuntahirunrat, “Temperature-insensitive voltage-to-current converter and its applications,” IEEE Trans. Instrum. Meas., vol. 48, no. 6, pp. 1270–1277, 1999, DOI: 10.1109/19.816147.

License

Copyright (c) 2020 Миколи Олександровича Корчака (Автор)