Device for Automated Measurement of Volt-Ampere Characteristics

Abstract

The device, which allows automated measurement of volt-ampere characteristics of semiconductor devices, is developed.  The device is implemented using the microcontroller of STM32F4 series, DAC, voltage–current transform circuit, voltage and current sensor and a laptop with LabVIEW programming environment. A wide range of current measurement is possible - from 25 μA to 800 mA with current control up to 0,4 μA. The digital voltage value from the microcontroller is transmitted to the AD5624R DAC via the SPI interface. AD5624R is a 12 bit four channel DAC with built-in voltage reference of 2,5 Volts. Using two DAC channels allowed to increase the resolution of voltage control to up to 12 μV. The voltage-current transform circuit consists of two precision operational amplifiers AD8510 and OP97 with low offset voltage, n-channel and p-channel field-effect transistors with low leakage current and threshold voltage. In the device it is important to control the offset voltage in order to provide a minimum initial current through the sample tested. The schematic is discussed for expanding the measurement range and compensating for the error of the zero code from the DAC. In the circuit, coarse control of the output voltage is implemented with a step of 1,2 mV, and fine control - with a step of 12 uV. Two channels of the DAC channel C and D were used for this purpose. The device circuit also provides compensation for the error of the zero DAC code. Among the resistive current sensors, we chose the INA226 chip, which can be purchased on the so-called "breakout" board. This sensor is one of the most accurate among analogues, containing a 16-bit ADC and providing digitized values of current and voltage at the output. The developed device has a linear dependence of the code to current. The linearity of current control is confirmed to have the correlation coefficient 99,9%. The approach to calibrate the device is described, which will minimize the error and expand the range of measurements. In order to correct the INA226 readings, correction coefficients are used, so that the approximated line equation for the precise voltmeter readings and the INA226 readings match.  It is possible to use the approximated values of the current for obtaining the volt-ampere characteristic in the "subthreshold" region when the voltage on the sample is less than the threshold voltage and current values are low (less than 1 mA), and the correted values from INA226 for building the volt-ampere characteristic in the "upper threshold" region, when the voltage on the sample exceeds the threshold and current values are higher. Ref. 12, fig. 8.

Keywords

References

1. Kudrevatykh E. F., “Virtualnyy izmeritel volt-ampernykh kharakteristik poluprovodnikovykh priborov ASS-4211 [Virtual current-voltage meter of semiconductor characteristics Ass-4211], ” Novinki otechestvenoy izmeritelnoy tekhniki, pp. 17 -19. URL: http://www.kipis.ru/upload/kipis_articles/article_acc-4211.pdf.
2. Diakonov V, “Sovremennaya tekhnika i pribory ndlya izmereniya rezistivnosti i snyatiya VAKh [Modern technology and devices for measuring resistivity and the CVC], ” Komponenty i tekhnologii, № 10, pp. 137 – 144, 2010. URL: https://cyberleninka.ru/article/v/sovremennaya-tehnika-i-pribory-dlya-izmereniya-rezistivnosti-i-snyatiya-vah.
3. Potekhin. A, “Izmereniye volt-ampernykh kharakteristik poluprovodnikovogo dioda [Measurement of current-voltage characteristics of a semiconductor diode], ” Praktikum. – Nizhniy Novgorod: Nizhegorodskiy gosuniversitet, 2015. URL: http://www.lib.unn.ru/students/src/measurments.doc.
4. Nikiforov S, “Izmeritelnaya laboratoriya dlya kompleksnogo issledovaniya kharakteristik svetodiodov.primenyayemykh v sistemakh otobrazheniya informatsii, [Measurement laboratory for a comprehensive study LED characteristics. used in systems information display], ” Komponenty i tekhnologii, № 7, pp. 170 – 175, 2007. URL: https://kit-e.ru/assets/files/pdf/2007_07_170.pdf
5. Zaitsev. R, “Hardware Realization of the System for Automated Current-Voltage Characteristics Measurement for Semiconductor Devices”, International Young Scientists Forum on Applied Physics, Dnipropetrovsk, 2015. DOI: 10.1109/YSF.2015.7333225.
6. Quad, 12-/14-/16-Bit nanoDACs with 5 ppm/°C On-Chip Reference AD5624R/AD5644R/AD5664R, Data Sheet Rev. C, Analog Devices. URL: https://www.analog.com/media/en/technical-documentation/data-sheets/ad5624_5664.pdf.
7. Wells C., Chan. D, “High-Side Voltage-to-Current (V-I) Converter, ” TI Precision Designs: Verified Design, SLAU502, 2013. URL: http://www.ti.com/lit/ug/slau502/slau502.pdf.
8. Precision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers, Date Sheet, Analog Devices. URL: https://www.analog.com/media/en/technical-documentation/data-sheets/ad8510_8512_8513.pdf
9. Low Power, High Precision Operational Amplifier, Data Sheet (Rev. G), Analog Devices. URL: https://www.analog.com/media/en/technical-documentation/data-sheets/op97.pdf.
10. MCP4921/4922 12-Bit DAC with SPI™ Interface, Data Sheet, Microchip. URL: http://ww1.microchip.com/downloads/en/devicedoc/21897b.pdf.
11. Danilov A., “Sovremennyye promyshlennyye datchiki toka [Modern industrial current sensors], ” Sovremennaya elektronika, STA PRESS, pp.25 – 35, October 2004. URL: https://www.soel.ru/upload/clouds/1/iblock/6fc/6fc9682474ac98ea43ffdab5b08fbd92/200401026.pdf.
12. INA226 High-Side or Low-Side Measurement, Bi-Directional Current and Power Monitor with I 2C Compatible Interface, Datasheet, Texas Instruments. URL: http://www.ti.com/lit/ds/symlink/ina226.pdf.

License

Copyright (c) 2019 Дмитро Вікторович Гуменюк (Автор)